View Poll Results: How often do you clean your brake rotors (or rim surface) and pads?
Regularly (How often)
3
7.89%
Here and There
12
31.58%
No
23
60.53%
Voters: 38. You may not vote on this poll
How often do you clean your brake pads?
#1
Drip, Drip.
Thread Starter
Join Date: Oct 2020
Location: Southern Ontario
Posts: 1,575
Bikes: Trek Verve E bike, Felt Doctrine 4 XC, Opus Horizon Apex 1
Liked 193 Times
in
163 Posts
How often do you clean your brake pads?
I am referring to disc brakes here in specific, but this would very much apply to regular rim brakes as well.
After pulling out the pads on all three of my bikes, and scrubbing them down with a metal brush, I find that the braking performance is now stronger and smoother. I will now get into the habit of doing this regularly, as all three bikes had heavily caked on brake dust/dirt mixed together which is then glazed into the pad due to the heat. I used a softer bristle brush to remove excess dust after removing the dirty layer. Avoid using a rag unless it is perfectly clean as you will just rub oil into the pad.
After pulling out the pads on all three of my bikes, and scrubbing them down with a metal brush, I find that the braking performance is now stronger and smoother. I will now get into the habit of doing this regularly, as all three bikes had heavily caked on brake dust/dirt mixed together which is then glazed into the pad due to the heat. I used a softer bristle brush to remove excess dust after removing the dirty layer. Avoid using a rag unless it is perfectly clean as you will just rub oil into the pad.
#2
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 16,143
Bikes: Tarmac Disc Comp Di2 - 2020
Liked 5,404 Times
in
3,729 Posts
Almost never. Although sometimes I might get something on the rotors while cleaning or lubing my bike and I'll spray a little isopropyl or ethanol on them and wipe them clean.
#3
Drip, Drip.
Thread Starter
Join Date: Oct 2020
Location: Southern Ontario
Posts: 1,575
Bikes: Trek Verve E bike, Felt Doctrine 4 XC, Opus Horizon Apex 1
Liked 193 Times
in
163 Posts
Interesting how all three of my bike responded somewhat differently after doing the same pad and rotor cleaning for each set of brakes respectively.
#4
Drip, Drip.
Thread Starter
Join Date: Oct 2020
Location: Southern Ontario
Posts: 1,575
Bikes: Trek Verve E bike, Felt Doctrine 4 XC, Opus Horizon Apex 1
Liked 193 Times
in
163 Posts
good braking habits involve linear, gentle application of braking force, which allows for enough gentle heat transfer to ensure good bedding between rotor and pad while keeping the rotor surface relatively clean.
Doing hard, random stops, especially in dirty conditions is pretty awful for the longevity and overall performance of your brakes. keeping the surfaces clean and occaisonally applying some gentle braking down a steep hill would be really helpful in such conditions.
Doing hard, random stops, especially in dirty conditions is pretty awful for the longevity and overall performance of your brakes. keeping the surfaces clean and occaisonally applying some gentle braking down a steep hill would be really helpful in such conditions.
#5
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 16,143
Bikes: Tarmac Disc Comp Di2 - 2020
Liked 5,404 Times
in
3,729 Posts
I'm not sure I agree with the gentle braking. Especially if it's long periods going down long slopes. Gentle braking I reserve for the times I need to feather the brakes, usually the rear for me. Otherwise, when I need brakes, I use them. IMO, slowing down quickly generates less heat over all then dragging a brake forever to slow down. I'm not saying do a max effort braking though. Though depending on the situation and exactly how you are using the brakes, YMMV.
Likes For Iride01:
#6
Drip, Drip.
Thread Starter
Join Date: Oct 2020
Location: Southern Ontario
Posts: 1,575
Bikes: Trek Verve E bike, Felt Doctrine 4 XC, Opus Horizon Apex 1
Liked 193 Times
in
163 Posts
I'm not sure I agree with the gentle braking. Especially if it's long periods going down long slopes. Gentle braking I reserve for the times I need to feather the brakes, usually the rear for me. Otherwise, when I need brakes, I use them. IMO, slowing down quickly generates less heat over all then dragging a brake forever to slow down. I'm not saying do a max effort braking though. Though depending on the situation and exactly how you are using the brakes, YMMV.
#7
Guest
Sounds like you've got it figured out already -- I don't see the point of the thread/poll.
Likes For Rolla:
#8
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 16,143
Bikes: Tarmac Disc Comp Di2 - 2020
Liked 5,404 Times
in
3,729 Posts
For cars, trucks and even bicycles, most of the stuff I've read suggests firm braking is better for brake pad and rotor life. Dragging ones brakes is ineffective for stopping and just creates unnecessary heat which is bad for every thing.
Now if you are talking about hard stops where the bike or any other vehicle is going so fast that the braking can't be accomplished before the parts get too hot, then I might agree.
Likes For Iride01:
#9
Drip, Drip.
Thread Starter
Join Date: Oct 2020
Location: Southern Ontario
Posts: 1,575
Bikes: Trek Verve E bike, Felt Doctrine 4 XC, Opus Horizon Apex 1
Liked 193 Times
in
163 Posts
The pad compound for disc brakes on most bikes i've seen are high performance, designed primarily for hard, irregular use. These type of compounds are dusty and require more cleaning than others.
The linear use of brakes can't always be followed for safety reason. If you rarely get the chance to get some smooth, long stops in, you'll want to take apart your brakes to clean and allow for re bedding more often.
Assuming your pads are coming into contact with the rotors evenly, occasional linear, controlled stops at maybe 75% reasonable effort without locking your tires is super critical for long term performance.
Last edited by Moisture; 05-02-22 at 02:20 PM.
#11
Why is it that companies like Shimano that make disc brakes and pads never suggest these sorts of cleaning rituals?
Apart from sanding superficially contaminated pads, at best this is unlikely to do anything useful. You are probably far more likely to further contaminate your pads than you are to restore them using the procedure you suggest.
Apart from sanding superficially contaminated pads, at best this is unlikely to do anything useful. You are probably far more likely to further contaminate your pads than you are to restore them using the procedure you suggest.
Likes For Polaris OBark:
#12
Guest
Likes For Rolla:
#13
Drip, Drip.
Thread Starter
Join Date: Oct 2020
Location: Southern Ontario
Posts: 1,575
Bikes: Trek Verve E bike, Felt Doctrine 4 XC, Opus Horizon Apex 1
Liked 193 Times
in
163 Posts
Why is it that companies like Shimano that make disc brakes and pads never suggest these sorts of cleaning rituals?
Apart from sanding superficially contaminated pads, at best this is unlikely to do anything useful. You are probably far more likely to further contaminate your pads than you are to restore them using the procedure you suggest.
Apart from sanding superficially contaminated pads, at best this is unlikely to do anything useful. You are probably far more likely to further contaminate your pads than you are to restore them using the procedure you suggest.
It is an undeniable learning experience for fellows such as yourself
#14
Guest
Likes For Rolla:
#15
Senior Member
I will file the surface of rubber brake pads that are glazed or use the file to smooth them if they have a ridge (caused by rims that have an indentation) and then clean the rim using isopropyl alcohol. This can improve braking if the pads are still relatively pliant but not if they are old and hardened. This often provides some improvement in braking but falls short of what can be achieved by replacing the pads. Filing does not work for disc pads and I have not found a way to clean them but I do use isopropyl alcohol and sometimes Brakekleen to clean rotors. This can sometimes cure squealing but often replacement of pads and rotors is needed.
#16
Advanced Slacker
Join Date: Feb 2017
Posts: 6,252
Bikes: Soma Fog Cutter, Surly Wednesday, Canfielld Tilt
Liked 2,571 Times
in
1,451 Posts
I started to respond to all the things Moisture gets wrong in this thread, but it would be a lot easy to just state the parts I agree with.
.
.
.
That’s about it.
.
.
.
That’s about it.
Last edited by Kapusta; 05-02-22 at 03:57 PM.
Likes For Kapusta:
#17
Take the pads out and tap them on a hard surface. The "dust", which is from the pads themselves, will fall off. This the the magical force of gravity at work. Wipe off the pistons while you are at it.
#18
Happy With My Bikes
Join Date: Sep 2020
Location: Oklahoma
Posts: 2,480
Bikes: Hi-Ten bike boomers, a Trek Domane and some projects
Liked 2,753 Times
in
1,280 Posts
I picked "No" in the poll as that was the closest option to never. I don't consider brake dust to be contamination.
__________________
"It is the unknown around the corner that turns my wheels." -- Heinz Stücke
"It is the unknown around the corner that turns my wheels." -- Heinz Stücke
Likes For Chuck M:
#19
Senior Member
This is all nonsense...But then, that was a foregone conclusion, since Moisty is the OP.
It still makes for fun reading, though.
It still makes for fun reading, though.
Likes For Koyote:
#20
Senior Member
Join Date: Dec 2015
Location: Menomonee Falls, WI
Posts: 1,861
Bikes: 1984 Schwinn Supersport, 1988 Trek 400T, 1977 Trek TX900, 1982 Bianchi Champione del Mondo, 1978 Raleigh Supercourse, 1986 Trek 400 Elance, 1991 Waterford PDG OS Paramount, 1971 Schwinn Sports Tourer, 1985 Trek 670
Liked 1,078 Times
in
546 Posts
I’ve got one bike with some vintage Campy Omega dark anodized rims, on that one I clean the pads quite often, trying to keep brake surface from becoming silver. So far successful, my others with silver rims never.
Tim
Tim
#21
Shawn of the Dead
I squeeze the brakes easy when I wont to come to stop slowly, I squeeze them a bit harder when I want to slow down fast. I adjust them when needed. That about all the thought I put into the brakes. I figure they get clean enough when I clean the bike.
#22
Disco Infiltrator
Join Date: May 2013
Location: Folsom CA
Posts: 13,508
Bikes: Stormchaser, Paramount, Tilt, Samba tandem
Liked 2,150 Times
in
1,402 Posts
I can't recall ever having cleaned brake pads on any vehicle I've ever owned
__________________
Genesis 49:16-17
Genesis 49:16-17
Likes For Darth Lefty:
#23
Advanced Slacker
Join Date: Feb 2017
Posts: 6,252
Bikes: Soma Fog Cutter, Surly Wednesday, Canfielld Tilt
Liked 2,571 Times
in
1,451 Posts
I did actually just sand, torch, and clean the pads on the front of my mtb today. They somehow got contaminated. We’ll see if it helps.
#25
Drip, Drip.
Thread Starter
Join Date: Oct 2020
Location: Southern Ontario
Posts: 1,575
Bikes: Trek Verve E bike, Felt Doctrine 4 XC, Opus Horizon Apex 1
Liked 193 Times
in
163 Posts
The mechanical disc brakes on my Opus now have pretty sufficient stopping power after taking the pads out to sand them down twice. I also swapped the pads front to rear on the second go to help distribute things out a little. The pads seem to get contaminated easily which doesn't help when most of the use these brakes see is hard used, short distance speed scrubbing.