Handlebar Tape from the Top?
#26
Senior Member
Join Date: Mar 2007
Location: SF Bay Area, East bay
Posts: 7,981
Bikes: Miyata 618 GT, Marinoni, Kestral 200, Soma double cross 2002 Trek 5200, KHS Flite, Koga Miyata, Schwinn Spitfire 5, Mondia Special, Univega Alpina, Miyata team Ti, Santa Cruz Highball, Waterford rs11
Liked 3,064 Times
in
1,394 Posts
https://www.amazon.com/Drain-Sealing...108349571&th=1
#27
seņor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,646
Bikes: '70s - '80s Campagnolo
Liked 7,016 Times
in
3,455 Posts
It needn't look "ugly" if it's done with a bit of creativity and finesse. I cut mine to exactly 9mm in width and apply with the ends hidden at the bottom of the bar. I normally use the black finishing tape packaged with Fizik. It's much nicer than regular electrical tape. And, of course, I remove all labeling. But here, I wanted to use a bit of a contrasting color to match my toe clip straps, so I went with red electrical tape in two layers.
.
.
#28
Senior Member
Thread Starter
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 6,376
Bikes: 1989 Cinelli Supercorsa
Liked 3,328 Times
in
2,004 Posts
I never knew this was a "thing" until I started looking at this forum. In 35 years, I've never once seen tape wound top to bottom until I saw it done here. Every description of how to tape bars I've ever seen or read through those years has never shown the tape started from the top. I've even seen people put finishing tape on the bar ends--which seems very odd to me. Considering, you know, bar plugs and all.
I once had a guy bring his '57 Chevy in to have the steering wheel wrapped. I'd never been in a '57 Chevy, and my mind was blown at how long the bench seat was! The passenger door was a mile away! Anyway, I don't remember whether I started at the top or the bottom...
#29
Banned.
As I noted, if one uses the entire bar in their riding, at some point, no matter which end you begin wrapping from, you are going to be pushing against an edge - unless, as one member has suggested in this thread, you wrap separately from the brake lever hoods.
DD
#30
Senior Member
My bar tape wrapping preferences have never put me at a disadvantage.
Your results may vary.
Wrap on.
Your results may vary.
Wrap on.
#31
Edumacator
Join Date: Jan 2018
Location: Goose Creek, SC
Posts: 7,577
Bikes: '87 Crestdale, '87 Basso Gap, '92 Rossin Performance EL-OS, 1990 VanTuyl, 1980s Losa, 1985 Trek 670, 1982 AD SLE, 1987 PX10, etc...
Liked 3,597 Times
in
2,260 Posts
I have 13 flavors of electrical tape.
__________________
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super, 1971 Raleigh International, 1998 Corratec Ap & Dun, 1991 Peugeot Slimestone
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super, 1971 Raleigh International, 1998 Corratec Ap & Dun, 1991 Peugeot Slimestone
Likes For jdawginsc:
#32
I wrap my bars starting from the brake levers, up to the stem and down to the bar ends. Done it since the early 80's after having problems with catching the bar tape seams and eventually causing gaps on the wrap.
Never had the problem again after doing this method of bar wrapping.
Never had the problem again after doing this method of bar wrapping.
__________________
72 Line Seeker
83 Davidson Signature
84 Peugeot PSV
84 Peugeot PY10FC
84 Gitane Tour de France.
85 Vitus Plus Carbone 7
86 ALAN Record Carbonio
86 Medici Aerodynamic (Project)
88 Pinarello Montello
89 Bottecchia Professional Chorus SL
95 Trek 5500 OCLV (Project)
72 Line Seeker
83 Davidson Signature
84 Peugeot PSV
84 Peugeot PY10FC
84 Gitane Tour de France.
85 Vitus Plus Carbone 7
86 ALAN Record Carbonio
86 Medici Aerodynamic (Project)
88 Pinarello Montello
89 Bottecchia Professional Chorus SL
95 Trek 5500 OCLV (Project)
#33
1991 PBP Anciens
Join Date: Nov 2009
Location: Elburn, Illannoy
Posts: 726
Bikes: 1954 Robin Hood, 1964 Dunelt, 1968 Raleigh Superbe, 1969 Robin Hood, 197? Gitane, 1973 Raleigh SuperCourse, 1981 Miyata 710, 1990 Miyata 600GT, 2007 Rivendell Bleriot
Liked 498 Times
in
190 Posts
This is almost like an oil thread on a motorcycle forum. But I'll play.
I have wrapped top to bottom since 1970 on every bike I have owned but one. That one has foam based tape and bottom to top was the only way I could get it to look almost acceptable. Every other bike is cotton or cello. Just did one with cotton yesterday. Waiting for it to dry so it can be shellacked. I've never had a curling issue, either.
I have wrapped top to bottom since 1970 on every bike I have owned but one. That one has foam based tape and bottom to top was the only way I could get it to look almost acceptable. Every other bike is cotton or cello. Just did one with cotton yesterday. Waiting for it to dry so it can be shellacked. I've never had a curling issue, either.
#35
Senior Member
Thread Starter
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 6,376
Bikes: 1989 Cinelli Supercorsa
Liked 3,328 Times
in
2,004 Posts
Not true if wrapped properly.
#36
seņor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,646
Bikes: '70s - '80s Campagnolo
Liked 7,016 Times
in
3,455 Posts
I love how tight he pulls the tape. That's great. But he tapes outside-in. And he cuts off the tape at the lever, then begins again.
I tried twine once. And I've used embroidery thread a bunch. It always looks stylish to begin. But even if I cover it with shellac or clear nail polish, it always comes undone. And I feel myself consciously trying to avoid placing my hand there ever. So I'm back to just keeping it simple.
#37
Banned.
Dafuq you talking about - what is "wrapped properly"?
If you wrap starting from the bottom you expose the edges on the lower extensions and the drops. Duh. I think you just want to argue.
Hundreds of bars wrapped or not, it seems you don't pay much attention beyond what you want to see.
DD
If you wrap starting from the bottom you expose the edges on the lower extensions and the drops. Duh. I think you just want to argue.
Hundreds of bars wrapped or not, it seems you don't pay much attention beyond what you want to see.
DD
#38
Senior Member
I tried twine once. And I've used embroidery thread a bunch. It always looks stylish to begin. But even if I cover it with shellac or clear nail polish, it always comes undone. And I feel myself consciously trying to avoid placing my hand there ever. So I'm back to just keeping it simple.
(This photo was taken just after I did it.)
Likes For P!N20:
#39
elcraft
If it was good enough for Eddie, it was good enough for us
.
When Tressostar cloth tape was coolest, the standard seemed to be to tape from the top of the bars down to bar plugs ( No finishing tape was needed and any excess was tucked into the bars and secured with a bar end plug . The practical among us were advised to go with Black bar tape as it didnt reveal that you had to mess with your bicycle chain, during your ride. .The black tape became imbedded with dirt and grease. It developed a unique patina that spoke of long rides under less than perfect circumstances, A badge of honor of a sort .
my 75 Raleigh Super Course ( which I purchased new) has just such a patinated black Tressostar taping that is smooth and mildly shiny. They have been in place for better than 40 years. I have had a plan to install Kelly Take-Offs to create Brifters, but I havent been able to let go of this beautifully smooth and comfortable covering. It has an almost leather like quality- reminiscent of the one piece rubber coverings that were once found on Motobecane cycles of that era.
When Tressostar cloth tape was coolest, the standard seemed to be to tape from the top of the bars down to bar plugs ( No finishing tape was needed and any excess was tucked into the bars and secured with a bar end plug . The practical among us were advised to go with Black bar tape as it didnt reveal that you had to mess with your bicycle chain, during your ride. .The black tape became imbedded with dirt and grease. It developed a unique patina that spoke of long rides under less than perfect circumstances, A badge of honor of a sort .
my 75 Raleigh Super Course ( which I purchased new) has just such a patinated black Tressostar taping that is smooth and mildly shiny. They have been in place for better than 40 years. I have had a plan to install Kelly Take-Offs to create Brifters, but I havent been able to let go of this beautifully smooth and comfortable covering. It has an almost leather like quality- reminiscent of the one piece rubber coverings that were once found on Motobecane cycles of that era.
Likes For elcraft:
#40
Senior Member
First time I ever had to wrap my own bar tape, bought it from the local Ames, I read the instructions which said to go from the top to the bottom, took two rides to determine this was a total failure and I've never done it again. Went to the LBS months later and sucked up riding a crap tape job till then, bought new tape, looked at the local bikes, went home and did it right. The difference was obvious. I've seen it work well with cello which I never understood the logic of, no grip, padding, or sweat absorption, and have seen it work moderately well with cloth. With modern tapes, just not the right way to go.
#41
Senior Member
Join Date: Feb 2017
Location: Concord, NC
Posts: 744
Bikes: 1984 Bianchi Tipo Corsa, 1985 Cannondale SM600 (24/26)
Liked 405 Times
in
213 Posts
I always thought it looked "neater", plus it's the way I was taught at Schwinn Service School in the Eighties.
Last edited by Bianchi84; 04-02-22 at 10:13 AM.
Likes For Pogliaghi:
#44
Senior Member
Join Date: Dec 2015
Location: Menomonee Falls, WI
Posts: 1,863
Bikes: 1984 Schwinn Supersport, 1988 Trek 400T, 1977 Trek TX900, 1982 Bianchi Champione del Mondo, 1978 Raleigh Supercourse, 1986 Trek 400 Elance, 1991 Waterford PDG OS Paramount, 1971 Schwinn Sports Tourer, 1985 Trek 670
Liked 1,083 Times
in
548 Posts
Tape doesn’t move if you know what your doing.
Tim
Tim
Likes For tkamd73:
#45
Newbie
Mr. Fisher, slightly off topic, can you tell me what shade of yellow is used on your Colnago? I have one that's a similar color that I've been trying for years to get a match for touch up paint.
Thanks! Cheers, Glen
Thanks! Cheers, Glen
#46
Strong Walker
Thin tape that grips on its entire underside like Tressoplast or Benotto tape can be wrapped top-botton for a nice looking upper end without crutches like electrical tape and it can be finished at the bottom end by fixing the overlap inside the bar with the plug.
Thick (cork type) tape from bottom to top. Only the middle of it is supported by sticky, so the edges would roll in the grip area. Also there is no way to wrap the end in an aesthetically pleasing way
Thick (cork type) tape from bottom to top. Only the middle of it is supported by sticky, so the edges would roll in the grip area. Also there is no way to wrap the end in an aesthetically pleasing way
#47
Senior Member
Glen, unfortunately I don't know the exact color, as the bike came to me finished that way. I do plan on getting it matched for touch ups, but haven't gotten around to it yet.
#48
Senior Member
Thread Starter
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 6,376
Bikes: 1989 Cinelli Supercorsa
Liked 3,328 Times
in
2,004 Posts
Some beautiful workmanship there, Bianchi84, Pogliaghi and tkamd73.
#49
Full Member
Depends on whether you live in the northern or southern hemisphere.
#50
Senior Member
When I was riding / racing in the 70s, all my bars were wrapped top down. I had one set of bars (can't remember the brand) that had sort of a reinforced center where the stem attached. It had square edges that were, oddly enough, about the same thickness as wrapped bar tape (the cloth kind) so the top end of the tape was the same diameter as the center of the bars. Never once did I have any fraying or unwrapping of the tape.
The only reason I wrapped my current bike bottom up (with tape at the top, which I still think is ugly) is because I have a bar end Di2 junction, and it sort of requires taping in that manner.
The only reason I wrapped my current bike bottom up (with tape at the top, which I still think is ugly) is because I have a bar end Di2 junction, and it sort of requires taping in that manner.