Have you ever just bought junk?
#26
Sanford.
I did not know that!
#27
I am potato.
Join Date: Jun 2015
Location: Pacific Northwest
Posts: 3,344
Bikes: Only precision built, custom high performance elitist machines of the highest caliber. 🍆
Liked 1,877 Times
in
1,066 Posts
Hey VegasJen , don't feel bad. I once bought a carbon handlebar. The seller was showing it by holding it with his hand in the stem clamping area and making good eye contact. When I got home I realized it was because it looked like he had tried to crush the 31.8 bar in a 25.4 stem. When I flexed the drops around in relation to each other the bar made crinkling noises. In the trash it went.
I also got a too-good-to-be-true deal on a White Industries disc eccentric ENO single speed wheel set with an Mi5 front hub laced to Hed Belgium G rims. Sweet deal since the bearings in the rear had just been replaced!
As soon as I installed it in the bike, I could not get the wheel to line up straight. It turns out the original owner tried to overhaul the hub by twisting the eccentrics off like they threaded in, or something instead of undoing the one bolt each that held the eccentrics in the axle. Lord knows how hard he must've tried. The axle is 15mm in diameter and solid aluminum bar stock. $80 later a new from the factory not twisted axle assembly had it all repaired.
Don't worry about it. Just like the sage advice of don't ever lend money you expect to get back, don't ever buy an item from Craigslist you expect to work.
I also got a too-good-to-be-true deal on a White Industries disc eccentric ENO single speed wheel set with an Mi5 front hub laced to Hed Belgium G rims. Sweet deal since the bearings in the rear had just been replaced!
As soon as I installed it in the bike, I could not get the wheel to line up straight. It turns out the original owner tried to overhaul the hub by twisting the eccentrics off like they threaded in, or something instead of undoing the one bolt each that held the eccentrics in the axle. Lord knows how hard he must've tried. The axle is 15mm in diameter and solid aluminum bar stock. $80 later a new from the factory not twisted axle assembly had it all repaired.
Don't worry about it. Just like the sage advice of don't ever lend money you expect to get back, don't ever buy an item from Craigslist you expect to work.
Last edited by base2; 05-19-24 at 07:26 PM.
#28
All Campy All The Time
Join Date: Nov 2013
Location: Richmond, Virginia
Posts: 1,427
Bikes: Listed in my signature.
Liked 120 Times
in
66 Posts
I've done it too. Looked right at the blem, rubbed it, thought it would be ok, paid and took it home. Win some, lose some.
__________________
My C&V Bikes:
1972 Bottecchia Professional, 1972 Legnano Olympiade Record,
1982 Colnago Super, 1987 Bottecchia Team C-Record,
1988 Pinarello Montello, 1990 Masi Nuova Strada Super Record,
1995 Bianchi Campione d'Italia, 1995 DeBernardi Thron
My C&V Bikes:
1972 Bottecchia Professional, 1972 Legnano Olympiade Record,
1982 Colnago Super, 1987 Bottecchia Team C-Record,
1988 Pinarello Montello, 1990 Masi Nuova Strada Super Record,
1995 Bianchi Campione d'Italia, 1995 DeBernardi Thron
#29
Bike Sorceress
Brand new Clarks CMD-11 disc brake. Wanted to see if it was reliable enough to be worth stocking over other cheap calipers. The internals wore out before the first set of brake pads was used up. Had to be overhauled halfway through it's short life. It did have outboard pad adjustment like a BB7 though, so at least it was quite easy to set up.
#30
Senior Member
Join Date: Jul 2009
Posts: 6,505
Bikes: Colnago, Van Dessel, Factor, Cervelo, Ritchey
Liked 8,316 Times
in
3,304 Posts
#32
Dirty Heathen
Join Date: Oct 2015
Location: MC-778, 6250 fsw
Posts: 2,278
Bikes: 1997 Cannondale, 1976 Bridgestone, 1998 SoftRide, 1989 Klein, 1989 Black Lightning #0033
Liked 988 Times
in
575 Posts
It happens. I bought a well used ‘89 Cannondale R500 with the intention off making an inexpensive training bike.
By the time it was all said and done, I’d have replaced everything but the serial number, and I probably could have gotten onto any of a number of newer (but lower spec) bikes that would have been ready to ride for the same money.
By the time it was all said and done, I’d have replaced everything but the serial number, and I probably could have gotten onto any of a number of newer (but lower spec) bikes that would have been ready to ride for the same money.
Last edited by Ironfish653; 05-19-24 at 10:35 PM.
#33
Grupetto Bob
Join Date: Sep 2020
Location: Seattle-ish
Posts: 6,977
Bikes: Bikey McBike Face
Liked 6,639 Times
in
3,356 Posts
And you acted so excited when I sold it to you at a “buddy price”.
__________________
Road 🚴🏾♂️ & Mountain 🚵🏾♂️
Road 🚴🏾♂️ & Mountain 🚵🏾♂️
#34
Senior Member
Join Date: Oct 2013
Location: Mich
Posts: 7,875
Bikes: RSO E-tire dropper fixie brifter
Liked 3,311 Times
in
2,100 Posts
Likes For Troul:
#35
Senior Member
Likes For Trakhak:
#36
Commuter
Join Date: Jun 2022
Location: SE Wisconsin, USA
Posts: 742
Bikes: Main Bikes: 2023 Trek Domane AL3, 2022 Aventon Level.2 eBike, 1972 Schwinn Varsity, 2024 Priority Apollo 11
Liked 519 Times
in
278 Posts
I did buy one bike a lot of folks consider junk: my 1972 Schwinn Varsity.
I was working on it yesterday. Started off thinking: "I'll clean and lube the chain."
Shifting to the big chainring on the front was never satisfactory. Looking at it, the front derailleur was rubbing on the inside of the guard. I moved it up, but found that it just doesn't have enough throw, even with the limit stop screws adjusted all the way.
I can look past it being really heavy, but only being able to use 5 speeds is kind of bogus.
They are very heavy, but I like the feel and look of them. I'm sure they were designed properly and would shift to the big chain ring, but I'll be damned if I can figure it out. Might have to take it to the local tech, but I hate to drop any more money into it, as the frame is a smidge too small for me anyway. Might be time to pass it on at a loss, having gotten my nostalgic thrill out of it. Or just hang it on the wall and admire it over a beer from time to time.
I was working on it yesterday. Started off thinking: "I'll clean and lube the chain."
Shifting to the big chainring on the front was never satisfactory. Looking at it, the front derailleur was rubbing on the inside of the guard. I moved it up, but found that it just doesn't have enough throw, even with the limit stop screws adjusted all the way.
I can look past it being really heavy, but only being able to use 5 speeds is kind of bogus.
They are very heavy, but I like the feel and look of them. I'm sure they were designed properly and would shift to the big chain ring, but I'll be damned if I can figure it out. Might have to take it to the local tech, but I hate to drop any more money into it, as the frame is a smidge too small for me anyway. Might be time to pass it on at a loss, having gotten my nostalgic thrill out of it. Or just hang it on the wall and admire it over a beer from time to time.
#37
Senior Member
Well, I have bought about 8 saddles and still have sit-bone pain on one side. At 255 I feel too fat to go to a proper fitter though, I am weakening. Does that make all of these expensive saddle junk?
#38
Senior Member
Join Date: Dec 2015
Location: Menomonee Falls, WI
Posts: 1,863
Bikes: 1984 Schwinn Supersport, 1988 Trek 400T, 1977 Trek TX900, 1982 Bianchi Champione del Mondo, 1978 Raleigh Supercourse, 1986 Trek 400 Elance, 1991 Waterford PDG OS Paramount, 1971 Schwinn Sports Tourer, 1985 Trek 670
Liked 1,083 Times
in
548 Posts
As an occasional Amazon user, of course I have! Fortunately they take it back.
Tim
Tim
#39
Geared torque-multiplier for lug nuts and such, broke first time I tried it, looked like die-cast pot metal, brought back to Harbor Freight. Same for 1/2" female to 3/8" male square drive socket wrench adaptor, broke immediately as I tried to torque lug nut to spec, brought back to Harbor Freight. Same for screwdriver security bit set, bits broke instantly, brittle as glass, brought back to Harbor Freight.
#40
But it makes sense to me. If you have tried 8 different saddles and still have the same issue, then maybe it isn’t the saddle?
#41
Senior Member
Geared torque-multiplier for lug nuts and such, broke first time I tried it, looked like die-cast pot metal, brought back to Harbor Freight. Same for 1/2" female to 3/8" male square drive socket wrench adaptor, broke immediately as I tried to torque lug nut to spec, brought back to Harbor Freight. Same for screwdriver security bit set, bits broke instantly, brittle as glass, brought back to Harbor Freight.
#42
Klaatu..Verata..Necktie?
Join Date: May 2007
Location: SF Bay Area
Posts: 19,392
Bikes: Litespeed Ultimate, Ultegra; Canyon Endurace, 105; Battaglin MAX, Chorus; Bianchi 928 Veloce; Ritchey Road Logic, Dura Ace; Cannondale R500 RX100; Schwinn Circuit, Sante; Lotus Supreme, Dura Ace
Liked 13,232 Times
in
6,797 Posts
I've been lucky so far, but I could easily imagine me ignoring some fatal defect, or just doing a cursory inspection of something because I don't want to be a jerk to a stranger in person*. I have yet to turn down something that I went to look at, but they all turned out okay.
*online with all of you clowns, being a jerk just comes natural to me.....
*online with all of you clowns, being a jerk just comes natural to me.....
__________________
"Don't take life so serious-it ain't nohow permanent."
"Everybody's gotta be somewhere." - Eccles
"Don't take life so serious-it ain't nohow permanent."
"Everybody's gotta be somewhere." - Eccles
#43
Senior Member
A very experienced fitter said that serial saddle buyers usually have some other underlying issue unrelated to the saddle. Either that or they are just really bad at choosing a saddle!
But it makes sense to me. If you have tried 8 different saddles and still have the same issue, then maybe it isn’t the saddle?
But it makes sense to me. If you have tried 8 different saddles and still have the same issue, then maybe it isn’t the saddle?
Likes For howsteepisit:
#44
I am pretty sure it's not the saddles, it would appear that I have some kind of leg length discrepancy or a twist to my pelvis. My Dumb Purchase was buying evermore saddles and not paying attention to how I feel on the bike. A fitting hereabouts is $475 so next month I will do that and see if we can figure out the cause of my discomfort and fix it. I am getting tired of being limited to 40 miles due to pain, not fitness.
#46
Grupetto Bob
Join Date: Sep 2020
Location: Seattle-ish
Posts: 6,977
Bikes: Bikey McBike Face
Liked 6,639 Times
in
3,356 Posts
Sure I have bought junk. Bought a stem computer mount which had a flat mounting surface where the bolts on the stem are in concave inserts. Into the bin.
__________________
Road 🚴🏾♂️ & Mountain 🚵🏾♂️
Road 🚴🏾♂️ & Mountain 🚵🏾♂️
#47
I bought tons of stuff in between those purchases which were cheap, but all fine. Favorite was a heavy cotton canvas riggers bag for $10, that I gave the waxed cotton treatment, still use a dozen years on:
Those red handled stainless steel heavy shears were also nice, and the plastic parts boxes were cheap.
Those red handled stainless steel heavy shears were also nice, and the plastic parts boxes were cheap.
Last edited by Duragrouch; 05-22-24 at 02:58 AM.
#48
Senior Member
Join Date: May 2014
Location: USA
Posts: 1,953
Bikes: 1996 Trek 970 ZX Single Track 2x11
Liked 638 Times
in
484 Posts
Only once have I needed something fairly quickly, where I didn't do the research and evaluate alternatives much: the purchase of a simple single-speed Kent LaJolla step-thru bike, for a "beater" around-town bike.
Worked well enough. Single-speed, coaster brake, nothing much to go wrong with it. Needed to replace the seatpost, but that was it. Comfortable. And almost certain to avoid the light-finger-Louie types every town finds now and then. Dead simple to maintain. A simple u-lock kept it safe.
I suppose one could call it junk. I did. But it never failed me.
Worked well enough. Single-speed, coaster brake, nothing much to go wrong with it. Needed to replace the seatpost, but that was it. Comfortable. And almost certain to avoid the light-finger-Louie types every town finds now and then. Dead simple to maintain. A simple u-lock kept it safe.
I suppose one could call it junk. I did. But it never failed me.